Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hypercom ICE 4000
Summary of Contents for Hypercom ICE 4000
- Page 1 ICE 4000 Hardware and Installation Manual Version 1.0 May 8, 2000...
- Page 2 Corporation. NOTICE Hypercom Corporation reserves the right to make changes to the publication at any time and without notice. The information furnished in this publication by Hypercom Corporation is believed to be accurate and reliable; however, Hypercom Corporation assumes no responsibility for its use. Any error in identifying or reflecting any proprietary marks or notices is inadvertent and unintentional.
- Page 3 TV reception requiring the operator to take whatever steps necessary to correct the interference. Repair work on this device (equipment) must by done by Hypercom Corporation or an authorized repair station. This equipment has been tested and found to comply with the limits for a class B digital devise, pursuant to Part 15 of the FCC Rules.
- Page 4 Installing the ICE 4000 Paper Roll........
- Page 5 ICE 4000 Hardware and Installation Manual 940265-001...
- Page 6 ICE 4000 under panel connections ........
- Page 8 Introduction This book, ICE 4000 Hardware and Installation Manual , is a comprehensive guide to working with the Hypercom ICE 4000 terminal. Guide Organization This book is designed to provide you with information relevant to Hypercom equipment. This book is...
- Page 9 Caution advises that a negative result such as a loss of data may occur. ARNING Warnings provide information that is essential to the safety of the user, the equipment, or both. Failure to do as instructed may result in physical damage. ICE 4000 Hardware and Installation Manual 940265-001...
-
Page 10: Terminal Information
C H A P T E R Equipment Information This chapter provides an overview of the Hypercom ICE 4000 terminal. Included are the features and benefits of the device. Terminal Information The Hypercom ICE 4000 terminal is a fully functional terminal that supports draft capture, check verification and guarantee, authorization, debit, and on-screen advertising through Term-Master Suite and ICE-PAC. -
Page 11: Features
1.5 MB available Full track 1 & 2 simultaneous card Integrated PIN and signature reader capture pads Multi-tasking operating system Dial line operation Electronic receipt capture Smart card support On-screen advertising available Multi-host application support ICE 4000 Hardware and Installation Manual 940265-001... -
Page 12: Ice 4000 Hardware Features
Equipment Information ICE 4000 Hardware Features The following is a list of the ports and features of the ICE 4000 terminal: Comm Port The RS232 comm port allows the ICE 4000 terminal to communicate with external devices such as an ECR (electronic cash register), OCR (optical character reader) wand, and a bar code reader. -
Page 13: Terminal Initialization
Chapter 1 Terminal Initialization Automated Terminal Configuration is downloaded from the host or from the Hypercom Term- Master application. Term-Master terminal profiles are downloaded through terminal initialization to meet the specific requirements of merchant categories such as restaurants for tips, retail, supermarkets, and the hospitality industry. -
Page 14: Financial Integrity
Fast Response Times The fast response time of the ICE 4000 terminal is the direct result of the efficient SDLC protocol, which permits pre-dialing and message compression. At a speed of 9600 bps, EFT messages of 150 characters are transmitted in 0.8 seconds, increasing throughput four to ten times over traditional 300 bps Asynchronous terminals. -
Page 15: Networking Efficiency
Screen images are downloaded through ICE-PAC and Term-Master Suite. Using an optional modem, a merchant can install the ICE 4000 terminal through the menu-driven procedure that identifies the telephone line profile for tone or pulse, or PABX access code, prompts for the telephone numbers for initialization and network management, and prompts for a unique terminal identification number with optional check digit. - Page 16 C H A P T E R Equipment Installation This chapter describes how to install the ICE 4000 terminal.
- Page 17 Chapter 2 The ICE 4000 underpanel connectors include power, PIN, battery and SAM chip panels, and line ports. Paper roll lock switch Line port RS232 PIN port Power switch Power port Contrast Control Dial SAM chip access panel Battery pack panel Figure 2-1.
-
Page 18: Turning On The Terminal
Equipment Installation Turning On the Terminal The ICE 4000 terminal operates using a +12 Vdc power cable in conjunction with a 110-Volt grounded power receptacle. Step-by-Step To turn on the ICE 4000 terminal: 1. Connect the +12 VDC power cable from the AC adaptor to the terminal power socket labeled PWR . -
Page 19: Installing The Ice 4000 Paper Roll
3. Feed the paper evenly into the paper feed slot at the rear of the ICE 4000 terminal. 4. When the paper appears, close the paper bucket cover. Slide the Paper roll lock switch to the left. -
Page 20: Ice 4000 Terminal
The ICE 4000 uses a Lithium Ion battery. The ICE 4000 has built-in circuit protection and battery charger. If using the ICE 4000 as a mobile unit, allow the ICE 4000 terminal to be plugged in and powered up for 4 to 6 hours. This allows the battery to fully charged. Use the following procedures to access the battery pack. -
Page 21: Ice 4000 Terminal
Chapter 2 Adjusting the Display Contrast The ICE 4000 uses a contrast control dial to adjust the display. The contrast control dial is located on the side of the ICE 4000 terminal. Step-by-Step To adjust the contrast on the ICE 4000 terminal: 1. - Page 22 We Welcome Your Comments Please fax this page with your comments to Hypercom Corporation at 602.504.4990 Document Number: 940265-001 1. In one word, how would you describe this guide? _________________________________________ 2. How do you use this guide? I read it from beginning to end.
- Page 24 Hypercom Document Number 940265-001 ICE 4000 Hardware and Installation Manual, Version 1.0 Printed in the USA...